Hit Signs

Guide

Florida sun, salt air and storms wear out each part of your sign at its own rate.

We explain which faces, films, LEDs and mounts wear first in Florida weather, how Florida's building code plans for wind, and what to check on your own building.

Call Tom 727-370-5060
Windows along a covered marina walkway printed with a speeding boat on dark blue water and the words Ahead of the current
We put a printed boat graphic across the panes of a window along PORT 32 Marina's covered walkway in Tierra Verde.

What Florida weather does to your sign

Each kind of weather works on a different part of your sign. Pick one to jump to its section.

Sun and heat
Sun fades faces and film, and heat shortens the life of LEDs and power supplies.
Rain and standing water
Water gets into letters, walls and pole bases through seams, holes and low spots.
Salt and exposure
Where exposure is severe, fasteners in masonry call for stainless steel instead of galvanized.
Wind
Wind pushes on faces and mounts, which is why large faces are stiffened and held in their frames.
Storms and surges
Surges and dirty power can trip power supplies, and moisture shortens LED life.

Sun works on your sign faces first.

Acrylic has historically held its color better, and polycarbonate resists breaking better; UV-stabilized polycarbonate grades have improved. One polycarbonate maker claims 30 times the impact strength of acrylic and offers limited warranties against breakage, yellowing and light loss.

Low-grade acrylic fades off your brand color, so one trade source recommends colorfast acrylic at the standard 3/16-inch face thickness.

Large flat faces can blow out in wind. Big cabinet faces are pan-formed, with a molded rim that stiffens the edge, and held in with dog strips, hanger bars and tie-back bars. Flex faces can loosen and shift in wind, which shows as spots and stripes when your sign is lit.

When one panel in a sign is replaced, the older faces beside it can look a different color, so plan face replacements together where you can.

Published outdoor ratings for vinyl and film

These are the makers' own ratings for vertical surfaces in a moderate climate. Hotter, sunnier regions are rated lower, and none of these figures is our warranty.

  • Cast cut vinyl lettering (ORACAL 751C)ORAFOL technical data sheet
    Up to 8 years for black and white, 7 for colors, 5 for metallic
  • Day/night film for lit faces (3M 3635-222)3M, as listed by a distributor
    7 years
  • Intermediate cut vinyl lettering (ORACAL 651)ORAFOL technical data sheet
    Up to 6 years for colors, 4 for metallic, 3 for brilliant blue
  • Frosted glass film (Avery Dennison Dusted Glass)Avery Dennison data sheet
    Up to 5 years outdoors, 9 indoors
  • Aluminum composite panel (DIBOND)3A Composites
    Long-term exterior use, up to 5 years
  • 13 oz banner vinylA banner seller's figure, not a maker's rating
    3 to 5 years with proper mounting
  • Higher-grade perforated window filmClear Focus
    Up to 3 years
  • Printed perforated window film3M lists one year unprinted; Avery Dennison lists one year printed
    About 1 year
Makers cut these ratings for hotter, sunnier climate zones: one maker's example takes 20 percent off a vertical rating in its second zone. Horizontal surfaces are rated far shorter than vertical ones.

Makers cut these ratings for hotter, sunnier climate zones: one maker's example takes 20 percent off a vertical rating in its second zone. Horizontal surfaces are rated far shorter than vertical ones. Choose your film for how long you need your graphics to last.

An installer in a boom lift basket works on tenant panels at the top of the Beach Plaza pylon
We applied tenant lettering to Beach Plaza's pylon panels from a boom lift. Each tenant's panel is a face held in the pylon's frame.
Bay Point Middle School storefront windows printed with the school name and FALCONS RISE
We made Bay Point Middle School's exterior window perfs with the school's name and values. Printed perfs carry a shorter outdoor rating than cut vinyl lettering.

Water gets into lit signs through seams and holes.

A lit sign in a wet location that is not listed as watertight needs drain holes, called weep holes, at its low points. Pinellas County's sign inspection instructions ask for a photo of them.

One fabricator reports that letters with trim cap, the plastic rim around a front-lit face, let water in at the face more often than trimless letters.

Some wholesale power supplies are rated for dry locations only, so where they sit, inside a raceway or behind your wall, matters.

Every hole through your wall is a path for water. Penetrations are sealed, and on EIFS the fasteners pass through the foam to the structure behind it. See raceway or direct mount and who connects power to your sign.

Heat and surges shorten LED life.

LED modules from major makers are rated beyond 50,000 hours, and some lines carry 10-year limited warranties. The trade treats about a 30 percent loss of light output as the end of an LED's life, and drivers, heat and moisture all shorten it.

Power supplies fail more often than LEDs because they have more parts. Common causes of outages include power supply safety shutoffs from surges and dirty power, heat inside a cabinet, shared or overloaded circuits, failing breakers, utility events and moisture.

A group of letters that goes dark together usually points to a power supply or your building's circuit, not the LEDs. Flicker after a storm can be a power supply shutting itself off to protect the LEDs.

Standing water and the wrong fasteners shorten a sign's life.

For fasteners in masonry, the Brick Industry Association calls for galvanized steel in normal exposure and stainless steel where exposure is severe. Exposed plain-steel fasteners can rust and crack plastic letters.

Leave at least 1/8 inch between the back of a mounted letter and your wall, so water and dirt do not collect behind it.

On a freestanding sign, standing water at the base corrodes poles and anchor bolts, and foundation caps are set at least 6 inches above grade.

After Florida's 2004 hurricanes, research for the Florida Department of Transportation found that cantilevered highway sign structures failed when twisting on the anchor rods cracked the concrete around the base, while the rods themselves held. A highway structure is not a business pylon, but the lesson carries over: the concrete around your bolts matters as much as the bolts.

Estate Cigars and Social at night, the ESTATE faces glowing near-white and the horse logo white and orange-red
Our channel letters light up Estate Cigars and Social at 1201 4th St S, St. Petersburg. Lit letters like these carry wiring and power supplies that have to stay dry.
Finished Mantione and Mantione pylon cabinet reading General and Cosmetic Dentistry, with a ladder at its base
Mantione and Mantione's finished pylon cabinet stands on a single steel column set in a raised concrete base on Duhme Road in Seminole.

Where wind and water act on your sign

These are the places a storm works on a pylon cabinet and on channel letters mounted on a raceway. Open each numbered point to see what happens there and what helps.

Where wind and water act on channel letters and a pylon cabinet (drawing)

Florida's building code designs your sign for wind, not for every storm.

Florida's building code covers signs, including the wind loads they must be designed to resist. St. Petersburg's sign permit checklist asks for freestanding sign installation drawings sealed for a 145 mph wind load, and for wall sign mounting details sealed by a state-certified design professional.

A design wind speed is a load your sign's structure is engineered to resist, not a promise that it will come through every storm. Faces can still blow out if they are not stiffened and retained, and one trade guide advises against changing faces on windy days.

Florida is moving to a new edition of its building code. The edition your sign is reviewed under depends on when your permit application is filed, so ask your building department which one applies. Our St. Petersburg permit guide covers the city's checklist.

After a storm, check your sign and your lease.

Your lease may set its own clock for repairs. One national landlord's tenant sign guide lets the landlord repair a tenant's sign at the tenant's cost, plus a fee, after 30 days' notice.

Cities also expect damaged signs to be repaired or taken down. In St. Petersburg, the city calls a sign damaged when more than a quarter of its structure or face is gone, or its supports are at risk of collapse, and a damaged sign can't stay that way for more than 90 days in a row. Once the city sends notice about a neglected sign, you have 60 days to put it right.

An old sign that no longer meets today's code may not be repairable as it stands once the damage is extensive. In St. Petersburg and unincorporated Pinellas, moving or replacing an older sign, or spending more than a quarter of its replacement cost on structural work, means it has to meet current code. In Tampa, any repair that touches the load-bearing parts of your sign needs a permit, and an older sign's structure can't be altered to prolong its life. These rules come from St. Petersburg's, Pinellas County's and Tampa's sign codes, and codes change, so confirm the current rule for your property with your city or county, or ask Tom, before you plan repairs.

Read old sign, new tenant for how those rules work, and take insurance questions to your insurer.

Dark and printed films change how your glass heats.

Dark or printed films change how glass heats in the sun, and one film maker warns this may lead to glass breakage. Check your glass type before covering a large pane with dark film.

Removing film can damage anti-reflective or abrasion-resistant coatings on some glass.

One-way perforated film works when the graphic side is brighter than the inside, so at night with your lights on, people outside may see in. Laminated perforated graphics keep rain from clogging the holes.

Clean film with a wet, non-abrasive cleaner and no solvents. See window perfs and window frosting.

Old graphics can come off without damage.

One maker's perforated film is made to come off within its expected life without heat or chemicals. Another maker's removal method uses gentle heat, lifts a corner with a razor and pulls the film back at a low angle, then cleans off the adhesive, taking care not to overheat or crack the glass.

Letters mounted on studs come off and go back up. Letters held with adhesive pads are hard to remove without damaging your wall.

What lasts, part by part

PartWhat wears it in FloridaPublished rating or ruleUsual fix
Lit facesSun and impactAcrylic holds color better; polycarbonate resists breakingA new face
Face vinylSun7 years for one day/night filmNew vinyl or a new face
Window filmSunAbout 1 year for printed perfs; up to 5 years outdoors for frosted filmNew film
LED modulesHeat and moistureBeyond 50,000 hours on major linesNew LEDs
Power suppliesSurges and heatThey fail more often than LEDsA new power supply
FastenersWater and exposureStainless steel where exposure is severeStainless replacements
Pole base and anchor boltsStanding waterFoundation cap at least 6 inches above gradeAn engineer's review
Trim cap seamsWaterLeak more often than trimless facesResealing or new faces

These ratings are the makers', not ours.

The ratings on this page are manufacturers' component ratings and warranties, such as 10-year limited warranties on some LED module lines and 5 years on one wholesaler's letters. They are not a Hit Signs warranty.

Tell Tom what your building faces, and send a photo.

Full sun, salt air and wind off the bay each change which faces, films and mounts make sense for your sign.

Call Tom 727-370-5060