Hit Signs

Dimensional letters

We design solid letters and logos for your wall, in metal or acrylic.

Dimensional letters have no lights inside, so they suit a business that closes by dark or a wall with good outside lighting. Tell Tom Coletta, who owns Hit Signs, whether your letters go outside or in your lobby, and we'll match the material to your wall.

Call Tom 727-370-5060
Shown
Jim Duprey Salon logo panel
Based in
St. Petersburg, Florida
Round JD Salon logo panel mounted flush on a gray side wall above a door
Jim Duprey Salon's round logo panel sits flush on gray stucco above the salon's side door.

Dimensional letters are solid letters that give your name depth by day.

Dimensional letters and logos are cut, cast or formed from metal, acrylic, PVC or foam, and mounted with nothing inside to light. By day they throw a shadow on your wall; at night they need outside light to be read.

Outside, they suit storefronts, offices and monument faces. Inside, they are the usual lobby logo. Cut letters come from your logo file on CNC routers and laser cutters.

Decide on lighting before you pick a material.

If you close before dark or your wall is lit from outside, solid letters can carry your name. If drivers need to read you at night, lit letters reach farther: in USSC Foundation road tests, internally lit signs were read 40 to 60 percent farther away, and an externally lit sign has to be about 40 percent larger to match.

See channel letters for letters lit from inside.

Choose your material

Match the material to where your letters go, the look you want and your budget. PVC and foam-core letters belong indoors only.

MaterialLookWhere it belongsGood to know
Flat cut metalCrisp solid letters with square edges, painted, brushed or patina finishedOutside or insideCut from aluminum or stainless alloys, or from bronze: one maker's examples include 3/8 inch bronze letters and a 1/4 inch logo.
Fabricated metalHollow letters with a face and sidesOutsideUsed for large exterior letters where solid plate would be too heavy.
Cast metalClassic cast letters and plaquesAsk for the maker's ratingA traditional look for building names and plaques.
Flat cut acrylicGlossy solid color or clearOutside or insideOne maker guarantees its pigmented white, black and clear acrylic for interior and exterior use.
Formed plasticThin formed letters that look deeper than they areAsk for the maker's ratingFormed letters run from 1/2 inch to 2.75 inches thick, in a set range of colors and fonts.
Flat cut PVCLightweight and economicalInside onlyIts edges are porous, and makers rate it for interior use.
Metal laminate on foamA thin aluminum or acrylic face on high-density foam, 1/2 to 3 inches thickInside onlyLooks like solid metal at a much lower weight.

Want the look of metal in your lobby without the weight? Metal laminate on foam reads as solid metal on an interior wall. Paint can be matched to your brand colors through systems that cross-reference PANTONE numbers, but paint and vinyl sold under one color name can look different, so compare samples side by side.

How your letters are mounted decides whether they can come off later without damage.

Flush stud mounting puts threaded studs in the backs of your letters, set into drilled holes filled with an adhesive such as silicone. Studs with spacers float your letters off your wall. Pad mounting holds letters about 3/8 to 1/2 inch off your wall, and tape is for flat interior surfaces.

Stud mounting handles rough stone or fluted masonry and lets your letters come off later without damage, while adhesive pads are hard to remove. Leave at least 1/8 inch between the backs of your letters and your wall so dirt and rainwater don't collect behind them.

Outdoors, galvanized fasteners suit normal exposure and stainless suits severe exposure. Exposed fasteners look bad and can rust or crack plastic letters.

Installers tape a full-size paper pattern to your wall in 5 to 6 foot sections, line it up to reference marks parallel to your building's face rather than to a bubble level, and center-punch hard surfaces such as concrete and stucco so the drill bit doesn't wander.

Compare four ways to mount your letters.

Pick a method to see the hardware and the gap it leaves behind each letter.

WallLetterStudAt least 1/8 inStreet
How letters mount: flush studs (drawing)
How it holds
Threaded studs in the backs of your letters go into drilled holes filled with an adhesive such as silicone, and at least 1/8 inch stays open behind each letter so dirt and rainwater do not collect.
Taking them down
Stud-mounted letters can come off later without damage, and studs handle rough stone and fluted masonry.

Jim Duprey Salon's round logo panels went from our shop table to the salon's walls.

These are round flat logo panels with a Greek key border rather than separate cut letters. Both went up flush on gray textured stucco, one over the front door and one over a side door, with no fasteners showing on their faces.

A panel on standoffs holds your logo off your wall.

A flat panel held off your wall on round standoffs is a common choice for office suites and practices. The panel's holes serve as the drilling template, and barrels and caps hold it a fixed distance off your wall.

See lobby and office signs for standoff panels and logos inside your office.

Unlit letters outside still need a permit, and lobby logos are not ADA signs.

St. Petersburg's sign permit checklist asks for an installation plan sealed by a state-certified design professional, with complete mounting details. Pinellas County has a wall sign permit type with no electrical work; its inspection asks for photos of every attachment, the fastener sizes before installation, your sign from near and far, a tape measurement of your sign face, and a weld certificate if anything was welded in the field.

Company names and logos, lobby logo walls included, are exempt from the ADA's visual and tactile sign rules. Signs that label permanent rooms are not. See ADA signs.

Sign permits in St. Petersburg walks through the city's process.

Solid letters last outside when a few details are right.

Florida sun, salt air and rain find the weak points. Signs in Florida weather covers them in more depth.

Gap behind letters
At least 1/8 inch behind your letters keeps water and dirt from building up against your wall.
Fasteners
Rust and cracking start at exposed or plain-steel fasteners, so outdoor letters go up on galvanized or stainless hardware.
Material
PVC and foam-core laminate are interior materials and do not belong outside.
Mounting
Stud-mounted letters can be removed and reset; letters on pads or tape are hard to remove without damage.

What to send Tom

These details let us pick a material for your wall and price your letters.

  • Your logo file, in a vector format if you have one.
  • A straight-on photo of your wall.
  • Whether your letters go inside or outside.
  • What your wall is made of: stucco, block, brick, metal panel or drywall.
  • Your wall width, or the letter height you have in mind.
  • The finish you want: a painted color, brushed metal or bronze.

Not sure how tall your letters should be? Our letter size calculator works it out from your reading distance.

Questions about dimensional letters

Channel letters are hollow, with a face and sides, and usually carry lights inside. Dimensional letters are solid pieces cut, cast or formed from metal, acrylic, PVC or foam, with no lights inside. See choosing a sign type.

Send Tom your logo and a photo of your wall.

Tell us whether your letters go inside or outside and what your wall is made of, and we send your price and a proof to approve.

Call Tom 727-370-5060