Hit Signs

Raceway or direct mount

Your letters can ride on a raceway, sit on a backer panel or mount straight to your wall.

A raceway means fewer holes and service from outside. Direct mount looks cleanest but needs holes at every letter and access behind your wall. Your landlord may already have decided for you.

Call Tom 727-370-5060
Taylor Sam's white channel letters and round logos on a dark fascia band above two wood-look canopies, by day
Our channel letters for Taylor Sam's sit on a dark fascia band above two canopies at 312 3rd St S, St. Petersburg.

There are five ways to mount channel letters.

Each method sets how many holes go into your wall, how your letters look by day and how they are serviced. Choose a method to see it from the side.

WallLetterStreet
How channel letters mount: raceway (drawing)
Holes in your wall
A raceway needs the fewest holes in your wall, because only the raceway is fastened to it.
How it looks
Your letters sit on a painted box that runs along your fascia.
Service
The power supplies sit inside the raceway, and lifting its top lets someone reach them.
Compare every mounting method

A raceway is a painted aluminum box behind your letters that holds the wiring and power supplies; one wholesaler sells raceway 5.5 inches high by 3.5 inches deep, in sections. A wireway is a slimmer box that carries wiring only. A backer panel is a painted, often shaped panel your letters sit on.

Each method fits a different wall and a different landlord.

MethodHoles in your wallWhere it fits
RacewayThe fewestStucco and EIFS walls, landlord sign bands, tenants who may move, and letters that need service from outside
WirewayMore than a raceway, fewer than directWhere your landlord specifies one, or where a landlord or code limits how far your sign stands off your wall
Direct (flush)Holes at every letterWalls with access behind them, and landlords that require flush letters
Backer panelThrough the panel into your wallHalo letters on a rough, dark or colored wall, covering old holes, and tight landlord color rules
Studs with spacersOne set for each letterHalo-lit and front-and-halo letters, standing about 1.5 to 2 inches off your wall

Block, brick, stucco and EIFS each take fasteners differently.

What your wall is made of, and what is behind its surface, decides the anchors that hold your letters.

Your wallWhat it means for your letters
Concrete block, common on Florida storefrontsAnchors hold most in solid concrete, then grout-filled block, then hollow block. Loads come from the anchor maker's tables, reduced near edges and between anchors. In hollow block, toggle bolts, hollow wall screws or small sleeve anchors are set into the cells.
BrickHollow brick takes toggle bolts, hollow wall screws or small sleeve anchors. Solid brick takes sleeve, wedge or lag shields, usually set in the mortar joints. Fasteners are galvanized steel for normal exposure and stainless steel where exposure is severe.
StuccoHoles are center punched and drilled so the bit does not wander, then sealed. What the stucco covers decides the anchor, and a St. Petersburg wall sign permit asks for a mounting detail sealed by a design professional.
EIFS (foam board with a stucco-like finish)Fasteners pass through the foam to the structure behind it, with spacers so tightening does not crush the foam, and every hole is sealed. Water gets in around fasteners, so fewer holes is better, which favors a raceway.
Metal or composite panelThe sealed mounting detail sets how your letters attach. Reflective panels can show the LEDs of halo letters in the reflection.
Canopy fascia or sign bandPlaza criteria can fix where letters go: centered on a defined band, within a set share of your storefront width, and on one facade material.

Every wall gets its own mounting detail. A St. Petersburg wall sign permit includes an installation plan sealed by a state certified design professional, with complete mounting details.

Every hole in your wall is a path for water, so how it is sealed matters.

Raceways and wireways need fewer holes than letters mounted one by one, and a raceway needs fewer than a wireway. Unsealed holes let water into your wall, and EIFS suffers most.

One LED maker's installation guide calls for non-hardening outdoor caulk on openings under 1/2 inch, and a metal patch fastened with screws or rivets and then caulked on larger ones. Wiring that passes through your wall to power supplies inside runs through a listed bushing or pass-through.

Two of our St. Petersburg jobs show what can sit behind channel letters.

A photo alone does not settle how a sign is mounted. Your wall, what is behind it and your landlord decide that for your letters.

Estate Cigars and Social storefront by day, with ESTATE channel letters and a horse-head logo on a dark fascia above a canopy
On our channel letters for Estate Cigars and Social, the smaller CIGARS & SOCIAL line sits on a dark horizontal bar painted to match the fascia.
Gold script letters reading Glo All Out above a black Beauty Bar and Spray Tan Spa panel on gray stucco
Behind our script letters for Glo All Out Beauty Bar in St. Petersburg you can see a gray rail, with the second line on a black panel below.

Direct-mount letters go up from a full-size paper pattern, not a bubble level.

For letters mounted straight to your wall, the fabricator supplies a full-size paper pattern with every hole marked. Installers tape it to your wall in 5 to 6 foot sections, lined up with reference marks parallel to your building rather than with a bubble level, because buildings are often out of level.

Patterns are not hung in rain or wind. On hard surfaces, each hole mark is center punched so the drill bit does not wander off it.

Ladders, scissor lifts and boom lifts are chosen by the height of your wall and the access in front of it, and anyone working from an aerial lift wears a harness tied off to the boom or basket.

Your sign outlet and disconnect decide where your raceway or wall opening goes.

Each tenant entrance in a commercial building needs a sign outlet on its own 20 amp circuit that serves nothing else. Your letters also need a disconnect: a switch at your sign, within sight of it, or one that locks off.

Class 2 power supplies sit in your raceway, inside your letters, behind your wall or in a listed enclosure. Some wholesale supplies are rated for dry locations only, so whether they sit in an outdoor raceway or behind your wall matters.

In Florida, a certified sign specialty electrical contractor may install and wire your sign up to its last disconnect, and electrical work on your building's side of that disconnect belongs to an electrical contractor. Our guide to who connects power to your sign explains the split.

Your landlord's sign criteria may already pick your mounting method.

Sign criteria are private rules on top of your city's code, and they vary from property to property. One published example comes from the national landlord Brixmor:

  • Drawings with letter sizes, a section, colors, wattage and every conduit and sleeve penetration go to the property manager before your letters are made.
  • Letters must be individual and lit from inside, with a UL rating, a photocell and an outside switch.
  • Letters have 5 inch returns on a 2 by 7 inch wireway, and raceway mounting is allowed only in select markets.
  • Cabinets and exposed lighting are not allowed, and your sign can be no wider than 80 percent of the usable storefront, on one facade material.
  • The tenant and their sign contractor are liable for damage from installation.

Send your criteria with your photo. Landlord sign criteria explains what they usually cover, and property managers can see signs for property managers.

St. Petersburg also limits where your letters can go on your building.

Each rule comes from the St. Petersburg sign code as published in November 2026 and applies to wall signs across the city. Sign codes change, so confirm the current rule for your property with the city, or ask Tom, before you order.

Windows and doors
Your letters can't go over your windows, doors or other openings in your wall.
How high
Wall signs stay at or below the third floor, unless another rule in the city code allows more.
Projecting signs
A sign that sticks out from your wall at a right angle, more than 6 inches, is a projecting sign, which the city treats as a type of wall sign. Its bottom has to be at least 8 feet off the ground.
Over the sidewalk
Only the downtown center (DC) and corridor commercial traditional (CCT) districts allow a wall sign over the sidewalk, and only with the city's minor easement permit. For a flat sign over the sidewalk, ask the city what clearance it wants.
Shared centers
In a center with three or more tenant spaces, your wall sign has to fit the uniform sign plan filed for the center.

Whether an old raceway can carry your new letters depends on what it is and what is inside it.

A raceway holds a sign's power supplies and wiring. Before it carries new letters, check its size and condition, the power supplies inside it, and how it is listed or labeled. At least one wholesaler excludes its raceway from its letters' UL listing, and electric signs must be installed according to their listing.

Power supplies have to be properly enclosed, and some are rated for dry locations only, so the supplies in an old raceway may not suit your new letters.

Send Tom a photo of your existing raceway, close enough to show its ends and any labels on it. An old sign on your new space covers reusing a raceway, cabinet or pole when you lease a space.

Questions about mounting channel letters

A raceway. Raceways and wireways both need fewer holes than letters mounted one by one, and a raceway needs fewer than a wireway.

Send Tom a photo of your wall.

A straight-on photo and a close-up of the surface tell us the most, and if there's a raceway or old holes, include those too.

Based in
St. Petersburg, Florida

Add photos of your building, your logo file and your landlord's sign rules if you have them. Up to 5 files, 10 MB each.

Add more details for Tom (optional)
Best way to reach you (optional)
Is there a sign there now?
Lit or not lit?

How we handle your details