Salons and spas
We design your salon's script name for the street and your logo for your reception wall.
Script names are harder to read at a distance than block letters, so we size yours to your road and carry the same look inside. Send Tom Coletta, who owns Hit Signs, your logo and your hours.
- Shown
- Glo All Out Beauty Bar, St. Petersburg
- Based in
- St. Petersburg, Florida

Your script name has to read from the street.
The International Sign Association advises against fancy or script lettering where legibility matters. If your script is part of your brand, keep it and size it up until it reads from the road.
Letter height starts from reading distance. A simple rule of thumb is about 1 inch of letter height for every 25 feet, and a wall sign that runs parallel to the road needs letters at least 70 percent larger than one that faces traffic.
A lit script needs room inside each stroke. Strokes narrower than about 1.5 inches leave no room to place LED modules well, and many letter makers won't build channel letters under about 8 inches tall.
Trimless front-lit letters keep the sharp points and fine details of a script that a trim cap edge can soften, and they cost more than trim cap letters. Logo and script letters shows how script shapes are built.
See how tall your salon name needs to be.
Choose script as your lettering style and the calculator reminds you to go up a size. The answer is a starting point from published industry formulas, and your city's allowance and your landlord's rules can cap it.
Suggested minimum letter height
10 in
(2 lanes x 10 + 30 ft from the curb to your wall) / 5 = 10.0 in before adjustments.
- A wall sign that runs parallel to traffic usually needs taller letters than a sign facing oncoming drivers.
You can get a metal look without solid metal.
If metal is over your budget, these are the common options, where each one can go and what it trades away.
| Option | Inside or outside | How it reads | What it trades away |
|---|---|---|---|
| Flat cut or cast metal | Inside or outside | Solid metal with crisp, sharp edges. | Cost: one large letter maker sells flat cut and cast metal as its top price lines. |
| Acrylic or formed plastic with a metallic finish | Inside or outside, when the maker rates it for outdoor use | A painted or brushed metal look on a lighter letter. | The metal look is a finish, so check its outdoor rating before it goes on your storefront. |
| Metal laminate on foam | Inside only | A thin aluminum or acrylic face on a high-density foam core, 1/2 to 3 inches thick. | It is not made for outdoor use, so it belongs on your reception wall. |
| Flat cut PVC | Inside only | Painted letters cut from plastic sheet. | Interior use only. |
Paint, printed vinyl and stock vinyl sold under the same color name can look different, and a lit color is the hardest to hold, so ask to see your color both lit and unlit before you approve it.
We mounted Jim Duprey Salon's round logo panels flush on the salon's stucco.
Jim Duprey Salon's logo became two round, flat panels with a Greek key border, one over the front door and one on the side wall.
Whether you need lit letters depends on your hours.
If you close before dark, you may not need lit letters at all. Non-lit dimensional letters or a flat panel need no electrical work.
If you book evenings or your street is dark, lighting earns its cost. In US Sign Council test-track research, internally lit signs read 40 to 60 percent farther than signs lit from outside, and a sign lit from outside has to be about 40 percent larger to match.
Front-lit letters glow through their faces, so your name is the brightest thing on your wall after dark.
Send Tom your hours with a photo of your storefront.
Inside, your reception wall and front door carry the same look.
Reception logos are often flat cut metal, acrylic or laminate letters, mounted on studs or tape depending on your wall. Stud-mounted letters go up from a full-size paper pattern with at least an eighth of an inch of space behind each letter, and they can come down later. Adhesive pads are hard to remove.
Your salon's name and logo on your reception wall carry no ADA requirements. Room and restroom signs at doors do.
On your front door, cut vinyl can carry your logo, your hours and a by-appointment line. Calendered cut vinyl such as ORACAL 651 is rated up to 6 years in colors, and cast ORACAL 751C up to 8 years in black and white, on vertical glass in a moderate climate.
For treatment rooms and front windows, dusted film gives a frosted look for privacy. It is rated up to 5 years outdoors and up to 9 years on interior glass.
Lobby and office signs, window graphics and window frosting cover each piece.
Moving into a space with a sign already on it? Start with what's there.
When you move into a new space, the last tenant's raceway, cabinet or pole may still be on your building. Many cabinets can take new faces without replacing their frames.
Your landlord's sign criteria can set your letter height, mounting method, colors and lighting, so ask for them before your logo is sized.
On a shared ground sign, your panel sits beside other businesses' panels, like the second panel on Elysian's sign. Old sign, new tenant and landlord sign criteria explain both.
Send Tom your logo and a photo of your storefront.
Tell us your hours, and we send your price and a proof to approve before anything is made.




