Hit Signs

Guide

Your sign permit in Pinellas County starts with finding which office reviews it.

We show you how to find your permitting office, what the county and Clearwater ask for, how county inspections work, and what to ask Largo and Seminole.

Call Tom 727-370-5060
ApplicationWhich officeAccess PortalPost permitCall 811Footer inspectionFinal photosPinellas CountyYour address
Reviewed
November 2026
Codes change
The official county and city pages are linked below.

Your mailing city is not always your permitting city.

St. Petersburg, Clearwater, Largo, Seminole and other Pinellas cities run their own building departments. Pinellas County's Building and Development Review Services reviews signs in unincorporated Pinellas and in Belleair Beach, Belleair Shore, Indian Rocks Beach, Safety Harbor and Oldsmar. Kenneth City splits its review with the county, and Belleair Bluffs moved to a private provider in August 2025.

To check where your property sits, look up your parcel on the Pinellas County Property Appraiser's site and read its tax district, because a St. Petersburg or Seminole mailing address can sit outside the city. The county's list of building departments shows who reviews each area.

Who reviews signs where

Contact details can change, so confirm them on the county's list before you go.

Where your sign isWho reviews itContact
Unincorporated Pinellas, Belleair Beach, Belleair Shore, Indian Rocks Beach, Safety Harbor and OldsmarPinellas County Building and Development Review Services440 Court St., Clearwater, 727-464-3888
St. PetersburgCity of St. PetersburgSee our St. Petersburg permit guide
ClearwaterCity of Clearwater100 S. Myrtle Ave., 727-562-4567
SeminoleCity of Seminole building division9199 113th St., 727-392-1966
LargoCity of LargoSee the county's list
Kenneth CitySplit between the city and the countyAsk the city which part it reviews
Belleair BluffsA private provider since August 2025Ask the town which provider reviews permits
Other Pinellas citiesSee the county's listCall the city's building department before you order

Some rules apply everywhere in the county.

Florida's building code covers signs, including the wind loads they must be designed to resist, wherever your sign stands.

Lit signs follow Article 600 of the National Electrical Code: a listed sign, a sign outlet on its own circuit at your entrance, a disconnect within sight or lockable, grounding and bonding, and drain holes in wet locations. Who connects power to your sign explains the split between sign and building wiring.

Florida law requires a call to Sunshine 811 at least two full business days before digging, and the locate ticket is good for 30 calendar days (Florida Statutes 556.105).

A building owner can act as the contractor on a commercial building they use themselves, not one for sale or lease, for work up to $75,000, and has to sign the application and a disclosure statement in person (Florida Statutes 489.103(7)). A tenant cannot use that exemption.

Florida's sign specialty electrical license covers your sign up to its last disconnect, and a registered, locally licensed electrical contractor works only where it is registered. The county's contractor licensing department notes that state law has changed local specialty contractor licenses, so ask the county which license it expects for the structural side of your sign.

The county has its own permit types and inspections.

If the county reviews your sign, you apply through its Access Portal, and many commercial projects need plans digitally signed and sealed by a licensed architect or engineer. Signs in unincorporated Pinellas also follow the county's own sign code, which requires zoning clearance and a permit before almost any sign goes up. Its limits are in the table below.

The county's sign permit types

  • Billboard
  • Change to an existing sign, or a face change
  • Monument, pylon or pole sign, with or without electrical work
  • Wall sign, with or without electrical work

A face change is a permit type of its own here. The county's page does not say when a face change needs one, so ask before you swap a face. Start from the county's commercial permits page.

What the county's sign code allows in unincorporated Pinellas

These limits come from the county's sign code and apply only in unincorporated Pinellas; each city has its own code. Sign codes change, so confirm the current rule for your property with the county, or ask Tom, before you order.

ZoneFreestanding sign heightFreestanding sign area per faceWall signs, all together
Office (LO, GO) and C-120 feet1 square foot per foot of lot frontage, up to 50 square feet1.75 square feet per foot of building frontage, up to 100 square feet
C-2 and E-2, off arterial roads25 feet1 square foot per foot of lot frontage, up to 100 square feet1.75 square feet per foot of building frontage, up to 150 square feet
C-2 and E-2, on arterial roads25 feet1 square foot per foot of lot frontage, up to 150 square feet1.75 square feet per foot of building frontage, up to 150 square feet
E-1, I and IPD25 feet1 square foot per foot of lot frontage, up to 75 square feet1.75 square feet per foot of building frontage, up to 150 square feet
Public and semipublic12 feet1 square foot per foot of lot frontage, up to 48 square feet1.75 square feet per foot of building frontage, up to 48 square feet

CP zones get up to 150 square feet a face on a freestanding sign and 150 square feet of wall signs; ask the county for their height. Freestanding signs stand at least 3 feet from the right-of-way, and in C-2, E-2 and CP zones a sign over 75 square feet stands 10 feet back. Put your street number on your freestanding sign and the county adds 8 square feet a face for it. Permanent window signs count toward your wall sign total.

More county rules apply to signs in unincorporated Pinellas.

  • Your sign has to meet the building, electrical and maintenance codes, and the property owner or tenant keeps it working and looking cared for.
  • A sign set at a right angle to your wall and sticking out more than 6 inches is a projecting sign.
  • Signs near driveways and corners stay clear of the sight lines set by the state's standards or the county traffic engineer.
  • A sign over 6 feet tall within 10 feet of the right-of-way needs a letter of no objection from the power company.
  • Signs with exposed bulbs are prohibited, and sign lighting has to be shaded, shielded or aimed away from neighboring properties.
  • Message centers hold each message at least a minute and dim at night.
  • Temporary window signs can cover up to a quarter of your glass, to a limit of 100 square feet.
  • Address numbers need no sign permit when they are at least 3 inches tall, in Arabic numerals and a contrasting color, on the front of your building.
  • Sandwich board signs are prohibited.
  • A sign for a business that has been gone from its location for more than 90 days in a row counts as abandoned, and abandoned signs are not allowed.

Older signs

You can maintain an older county sign and change its message. Move it, replace it, or spend more than a quarter of its replacement cost on structural work, and it has to meet current code. The county code also sets a deadline for older signs to meet current rules, with exceptions, so ask Pinellas County Zoning how it applies to your sign before you plan work on it. Old sign, new tenant explains how older signs are treated.

How a county sign permit runs

For permits the county issues, its March 2026 inspection instructions set this order.

  1. Step 1. Confirm the county reviews your address.

    Which office reviews your sign

  2. Step 2. Apply through the county's Access Portal, with sealed plans where your project needs them.

  3. Step 3. Post your permit, and post a Notice of Commencement on projects of $5,000 or more.

  4. Step 4. Call 811 at least two full business days before anyone digs a freestanding sign's footing.

  5. Step 5. Pass the in-person footer inspection before the concrete is poured.

  6. Step 6. Send your final inspection as photos and measurements through the VuSpex GO app.

    What the photos show

What your final inspection photos need to show

These come from the county's March 2026 inspection instructions and apply only to permits the county issues.

ItemWhat it showsSigns
Posted permitYour permit on siteAll signs
Attachments and fastener sizesHow your sign is fastenedAll signs
Face sizeYour sign face measured with a tapeAll signs
Sign in placePhotos of your sign from near and from farWall signs
SetbacksThe near and far setback measurements, how far your sign stands from the property linesFreestanding signs
Overall heightHeight from the ground to the top of your signFreestanding signs
Weld certificateA certified weld inspector's certificate, if anything was welded in the fieldAll signs
Listing markThe UL or other listing label on your signLit signs
DisconnectThe switch that cuts power to your signLit signs
Method of controlYour photocell, time clock or switchLit signs
Weep holesThe drain holes at your sign's low pointsLit signs
Breaker and panel scheduleThe breaker feeding your sign, marked on your panel scheduleLit signs

A freestanding sign's footer inspection is in person, and it has to pass before your final can be scheduled. The county's instructions: freestanding, lit, freestanding, not lit, wall sign, lit and wall sign, not lit.

Clearwater's application asks for a survey and sealed drawings.

Clearwater's sign permit application, revised January 2026, asks for:

  • A signed and sealed property survey.
  • A site plan with sight triangles and the setbacks to every freestanding or monument sign, with freestanding signs at least 5 feet from any property line.
  • An inventory of signs already on your property.
  • Construction and electrical specifications, including the UL listing, with commercial sign lighting no brighter than 5 foot-candles.
  • A structural drawing signed and sealed by a licensed Florida engineer or architect for any sign over 32 square feet.
  • A 3-square-foot address sign on every freestanding and monument sign, not counted in your sign area.
  • A notarized consent from the property owner when someone else signs, or a copy of your lease.
  • Your acknowledgment that nonconforming signs are subject to amortization.

Multi-tenant properties may use the city's Comprehensive Sign Program. The January 2026 form still cites an older edition of the Florida Building Code for wind loads, so ask the city which edition its review uses.

Largo and Seminole run their own reviews.

Largo reviews signs under its own code, and so does Seminole. Seminole's building division is at 9199 113th St., 727-392-1966.

Call each city's building or planning staff for its sign rules before you order, and check your tax district first, because parts of the Seminole mailing area may sit outside the city.

A crane lifts the Mantione and Mantione pylon cabinet while two men watch from the lot
Mantione and Mantione's pylon cabinet is our job on Duhme Road in Seminole, set here by crane.
An installer in a boom lift basket works on tenant panels at the top of the Beach Plaza pylon
We applied tenant lettering to Beach Plaza's pylon panels from a boom lift. Whether a panel change needs a permit depends on the city.

The same face change, city by city

Swapping a face or a tenant panel can be its own permit in one place and need no building permit in the next.

Where your sign isFace or panel change
Unincorporated Pinellas and county-served citiesA permit type of its own, listed as Change to Existing/Face Change; ask when one is required.
St. PetersburgNo permit for a face of the same size and material in a legal sign, as long as its structure meets Florida's building code and the city's design rules (St. Petersburg's sign code). See our St. Petersburg permit guide.
ClearwaterThe application has you acknowledge that nonconforming signs are subject to amortization; ask whether your change needs a permit.
Largo and SeminoleAsk the city.
Cities using Florida's model administrative rulesNo building permit for a face change when the cabinet, structure and equipment inside stay the same, where a city has adopted that rule.

If your sign was put up under older rules, read old sign, new tenant before you change it. See also signs for property managers.

A new edition of the Florida Building Code is coming.

Florida is moving to a new edition of its building code, along with a newer edition of the National Electrical Code. The edition your sign is reviewed under depends on when your application is filed, so ask your building department which edition applies when you file.

Who usually does what

This is the usual split between sign companies, landlords, engineers and electricians. Get your own split in writing before you order your sign.

TaskSign companyYouLandlordEngineerElectricianCounty or city
Sign criteria approvalPrepares drawingsAsks for approvalApproves
Sealed drawingsCoordinatesSealsReviews
Power to your signWires your sign, if licensedShows where the circuit isRuns the circuit beyond your sign's disconnectInspects
Application and feesUsually files, if licensedPays fees under your contractFiles a separate electrical permit, if neededIssues
Utility locateCalls 811Marks private lines
Final inspection photos on county permitsUsually takes and sends themGives site accessReviews them

Before you order any sign, get in writing who pulls your permit and whether the permit fee and engineering are in your price.

Short answers

Not always. Look up your parcel on the Pinellas County Property Appraiser's site and check its tax district, then find your office on the county's list of building departments.

Send Tom your address and tell us what you have in mind.

Tell us your address and town, what kind of sign you want and whether a sign is there now.

Call Tom 727-370-5060