Hit Signs

Front-lit channel letters

Front-lit channel letters glow through their faces, so your name reads at night.

LEDs inside each letter light its face while the sides keep their painted color. We match your face colors to your logo, and some colors read far better lit than others.

Call Tom 727-370-5060
Estate Cigars and Social at night, the ESTATE faces glowing near-white and the horse logo white and orange-red
Our channel letters light up Estate Cigars and Social at 1201 4th St S. At night the ESTATE faces glow near-white while the returns stay dark.

Light leaves a front-lit letter through its face.

Each letter is a shallow can: a flat back, side walls called returns, and a translucent face, usually 3/16 inch acrylic. LED modules glued to the inside back shine forward through the face, and a Class 2 power supply turns building power into low voltage for them. Open a numbered part of this drawing to see what it does.

LEDs inside light the translucent face, so your name glows toward the street.

Drawing of a channel letter cut in half on a wall, showing the face, trim cap, return, back, LED modules, power supply and racewayWallStreet
How a channel letter is built (drawing)

The inside of each can is painted highly reflective so the light spreads evenly, because an unfinished interior leaves dim spots and hot spots. A 3 inch return looks brighter than a 5 inch return, since light travels a shorter distance to the face. A trade rule of thumb is one strand of modules for every 5 inches of interior width, and strokes narrower than about 1.5 inches leave no room to place modules at all.

Your front-lit letters read as colored faces by day and glowing faces at night.

Signs lit from inside read farther at night. In US Sign Council test track research, they were read 40 to 60 percent farther away than signs lit from outside.

Taylor Sam's white channel letters and round logos on a dark fascia band above two wood-look canopies, by day
Lights off
Taylor Sam's channel letters at night, white faces glowing against dark returns
Lights on

Our channel letters light up Taylor Sam's at 312 3rd St S, St. Petersburg. By day you read white faces on a dark fascia, and at night the faces glow while the returns fade into the dark. Flip the switch to compare.

Taylor Sam's, St. Petersburg

Some face colors glow when lit, and some go muddy.

Red faces read very well lit. Dark blue and dark green absorb light and can look dull at night, so a navy or forest green brand needs a plan before your faces are made.

Ways to keep a dark brand color readable at night

  • Translucent vinyl comes in more colors than stock acrylic, and it can outline a letter (a reveal) instead of covering the whole face, which keeps your name readable when lit.
  • Day/night film shows one color by day and a different, brighter color when your letters are lit. One film of this kind, 3M 3635-222, uses a 15 percent perforated pattern.
  • One translucent digital print with a UV laminate carries more colors and gradients than cut vinyl.
  • The acrylic itself comes in several whites and in light-diffusing grades made to reduce LED hot spots.

Paint, printed vinyl and stock vinyl sold under the same color name can look different, and the lit color is the hardest one to hold. Where your brand colors must match, ask to see your colors lit and unlit before your faces are ordered. A screen or a printout will not show you how your faces look lit.

Estate Cigars and Social storefront by day, with ESTATE channel letters and a horse-head logo on a dark fascia above a canopy
By day Estate Cigars and Social's ESTATE faces read gold-tan. At the top of this page, lit at night, the same faces glow near-white.Estate Cigars and Social, 1201 4th St S

Trim cap or trimless changes the edge of your letters.

Trim cap is a plastic molding that holds the face of a front-lit letter to its returns. It has an aluminum core, comes 3/4 inch or 1 inch wide, and is bonded to the face edge with a plastic cement, rolled tight and left to cure. The face is then screwed through the returns, so it lifts off like a lid when a letter needs service.

Trim cap is quick, keeps cost down and hides small flaws. Its drawbacks show at the edge: visible gaps or waviness, a rim that is hard to paint a custom color, water that can funnel in at the face, and a shorter life outdoors.

Trimless letters skip the plastic rim. Their faces are held with screws and adhesive or an internal lip, so sharp points and fine details hold up, and they suit metallic or painted returns. They run roughly 6 to 28 inches tall and cost more than trim cap letters. Trimless letters over 48 inches often need polycarbonate faces, internal support or metal retainers.

Acrylic or polycarbonate faces

The standard front-lit face is 3/16 inch acrylic. Trade guidance calls for colorfast acrylic at that thickness, because low-grade acrylic fades off your brand color in the sun.

Polycarbonate faces are chosen where impact strength matters. SABIC, which makes LEXAN polycarbonate sheet, says it has 30 times the impact strength of acrylic and offers limited warranties against breakage, yellowing and light loss.

Lit letters need a sign circuit, a disconnect and a way to switch on at dusk.

Each tenant entrance in a commercial building needs a sign outlet on its own 20 amp circuit that serves nothing else (National Electrical Code 600.5(A)). Your letters also need a disconnect: a switch at your sign, within sight of it, or one that locks off (600.6).

Class 2 power supplies, listed for sign use, sit inside your letters, in a raceway or in a listed enclosure. Some wholesale supplies are rated for dry locations only, so where they sit matters.

A photocell turns your letters on at dusk and off at dawn, a time clock switches them on a schedule, and some signs use both. Some landlords require a photocell and an outside on/off switch, and do not allow a time clock alone.

Electric signs must be listed and installed according to their listing. The UL 48 standard covers custom signs, including channel letters, and the UL label on your letters or on each section shows they were built to it. When Pinellas County inspects a lit wall sign, the inspector asks for photos of the listing mark, the disconnect, the breaker and panel schedule, how your sign switches on, and the weep holes that let water drain out of each letter.

Who wires what, from your electrical panel to your letters, is in our guide to who connects power to your sign. For the city side, see channel letters in St. Petersburg.

Here is what fails first on lit letters, and how it is fixed.

LED module lines from major makers are rated for more than 50,000 hours, with component warranties of 5 to 10 years. Power supplies have more parts and fail more often than the LEDs. When lit letters go dark, the cause can be a power supply that shut itself off after a surge, heat, dirty power, a shared or overloaded circuit, a failing breaker, a utility event or moisture.

On trim cap letters, the face edge is where water gets in. Faces and films fade on their own schedules: low-grade acrylic fades first, and day/night film is rated for 7 years outdoors.

Fixes include a new power supply or new modules, or new faces and vinyl. For sun, salt air and storms, read signs in Florida weather.

Questions about front-lit letters

Red reads very well when lit. Check your exact red both lit and unlit before your faces are made, because the lit color is the hardest one to hold.

You can drive past our lit channel letters in St. Petersburg.

Estate Cigars and Social is at 1201 4th St S and Taylor Sam's is at 312 3rd St S. Drive past either one after dark.

Tell Tom about your lit letters.

Attach your logo and a photo of your building, and tell us your brand colors if you know them.

Based in
St. Petersburg, Florida

Add photos of your building, your logo file and your landlord's sign rules if you have them. Up to 5 files, 10 MB each.

Add more details for Tom (optional)
Best way to reach you (optional)
Is there a sign there now?
Lit or not lit?

How we handle your details